Hardware / Networking - Revision history

Strohmy: /* Network Setup for LAN sensors */

2019-07-05T09:07:49Z

‎Network Setup for LAN sensors

Strohmy at 08:29, 17 March 2019

2019-03-17T08:29:19Z

Strohmy at 08:23, 17 March 2019

2019-03-17T08:23:07Z

Strohmy: Created page with "To use {{ot}} with the supported network sensors you have to make sure that the computer which is running the {{ot}} software is in the same network like your connected sensor..."

2019-03-17T08:20:39Z

Created page with "To use {{ot}} with the supported network sensors you have to make sure that the computer which is running the {{ot}} software is in the same network like your connected sensor..."

New page

To use {{ot}} with the supported network sensors you have to make sure that the computer which is running the {{ot}} software is in the same network like your connected sensor.

'''Follow this steps to make sure your computer can see the sensor in the network:'''

*Open the Network Connections Window <code>Control Panel\Network and Internet\Network Connections</code>
[[File:Networkconnections01.png]]

*Right click on the Network adapter which is connected to the network where your sensor is connected too
[[File:Networkconnections02.png]]

*Left click ''Properties''
[[File:Networkconnections03.png]]

*Double click ''Internet Protocol Version 4(TCP/IPv4)''
[[File:Networkconnections04.png]]

*Give your computer a manual fixed IP and assign the Subnet Mask

{{WarningText|Make sure that the IP you assign to your computer is not used already from another device!}}

← Older revision		Revision as of 09:07, 5 July 2019
Line 28:		Line 28:
	{{WarningText\|Make sure that the IP you assign to your computer is not used already from another device!}}		{{WarningText\|Make sure that the IP you assign to your computer is not used already from another device!}}

		+
		+	'''Check the network connection - ping test'''
		+
		+	*Press Windows Key + R
		+	[[File:Win+r.png]]
		+
		+	*Type cmd into the Run window and press Enter
		+	[[File:Cmd.png]]
		+
		+	*Type ping the_IP_address_of_the_sensor and press Enter
		+	[[File:Ping02.png]]
		+
		+	*If the sensor is connected correct then you will get a reply from the sensor
		+	*If the sensor is not replying you have a wrong network setup
		+	[[File:Ping03.png]]

	==Setup for USB sensors==		==Setup for USB sensors==

← Older revision		Revision as of 08:29, 17 March 2019
Line 27:		Line 27:

	{{WarningText\|Make sure that the IP you assign to your computer is not used already from another device!}}		{{WarningText\|Make sure that the IP you assign to your computer is not used already from another device!}}
		+
		+
		+	==Setup for USB sensors==
		+
		+	{{ot}} supports the ''Hokuyo URG04 UG01'' sensor. This sensor has no network connection and uses a USB connection.
		+
		+	To make sure the sensor gets recognized from Windows and in the {{ot}} software you have to make sure that the serial COM port is setup correctly.
		+
		+	*Open the device manager and check which com port is assigned to the sensor
		+	*setup the same com port in {{ot}}

← Older revision		Revision as of 08:23, 17 March 2019
Line 1:		Line 1:
−	To use {{ot}} with the supported network sensors you have to make sure that the computer which is running the {{ot}} software is in the same network like your connected sensor.	+	==Network Setup for LAN sensors==
		+
		+	To use {{ot}} with the supported LIDAR network sensors you have to make sure that the computer which is running the {{ot}} software is in the same network like your connected sensor.